Author. Posted March 27. Hi, many thanks for reply, it is a 2.2 mk7 2013. looks at the diagram you just posted, it’s not in that location. took rear brake light unit out, the parking sensor cable looms goes up into the vehicle from underside via a rubber grommet and the into a block connector, (look in pic bottom right corner, wires hanging 2) Both front and rear sensors are connected to PSM_MZ module located behind glove box right side. You should check first that you have this module and the harness to it is full. 3) You need new indicator unit with parking sensor button. Get the current from the wires to connect your parking sensors to this one. Try it out all out. Install a parking sensor without drilling on a BMW X3. And to conclude, we will now present you the installation of a drill-free parking sensors system on a BMW X3. There are two options, the ultrasounds more weak because exposed to the shocks, and Park pilot malfunction service required. 90% of the time when as soon as I put the ignition on my 2014 transit custom limited it comes up on the dash saying ‘Park pilot malfunction service required’. I took it to a ford garage and they said it is the rear outer right hand side parking sensor, so I replaced it and it still hasn’t made any High in power, efficient in performance, reliable in service User-friendly design, ergonomic handle, solid construction. $63.38 - $128.49. Standard® Parking Aid Sensor. 0. # 1584236528. Ford C-MAX 2017, Parking Aid Sensor by Standard®. Standard® is a complete engine management import line that includes ignition and electrical relays Hemi 5.7. The Parking Sensor Module (Parktronics) is located to the left of the emergency brake, below the connectors for the drivers door accordion harness. You just need to pull the trim to the left of the emergency brake that goes across the drivers door rocker panel, then there are 3 nuts that hold the emergency brake on.
First entry in this topic courtesy tunne1rat: As some of you are now aware, the biggest problem with the s-max is the poxy alarm! The problem is caused by water getting into the alarm sounder module which is located under the front ns wheel arch. The only cure is to get the alarm sounder replaced at the dealers.
The airbag light on a Ford can come on for several reasons, including a faulty crash/weight sensor, a bad clock spring, a weak/dead battery, a bad belt pre-tensioner, damaged wiring etc. To find out, you need to read the codes with a scanner [2] that can read the airbag module, such as YOUCANIC full system scanner.

The cooling fan is powered by a relay in the Front Fuse Box, R12. This in turn is turned on the the ECR (engine control relay, I guess) relay R14. R14 is turned on by the ECM (aka ECU). The fan controlling module is also controlled by the ECM. Thus to run the fan, R12 needs to be on to supply power to the fan module, and the fan module will

4GesHH.
  • ybgn7w5ll5.pages.dev/317
  • ybgn7w5ll5.pages.dev/304
  • ybgn7w5ll5.pages.dev/142
  • ybgn7w5ll5.pages.dev/515
  • ybgn7w5ll5.pages.dev/927
  • ybgn7w5ll5.pages.dev/371
  • ybgn7w5ll5.pages.dev/708
  • ybgn7w5ll5.pages.dev/736
  • ybgn7w5ll5.pages.dev/291
  • ybgn7w5ll5.pages.dev/344
  • ybgn7w5ll5.pages.dev/976
  • ybgn7w5ll5.pages.dev/914
  • ybgn7w5ll5.pages.dev/287
  • ybgn7w5ll5.pages.dev/719
  • ybgn7w5ll5.pages.dev/259

    • ford c max parking sensor module location